5/21/2023 0 Comments Turn on disk led hp![]() However, in the graph of this measure LED status will be represented using the corresponding numeric equivalents only. The locator LED is illuminated to identify the disk.īy default, this measure reports the above-mentioned Measure Values while indicating the state of the LED of this disk. The values that this measure can report and the their corresponding numeric values are tabulated below: Indicates the current state of the LED of this disk. However, in the graph of this measure disk status will be represented using the numeric equivalents only. Initial status when the disk is first detected or powered on.īy default, this measure reports the above-mentioned Measure Values while indicating the status of this disk. The disk slot indicates that no disk is present. The disk is present and is properly communicating with the expander. The disk is present and has been spun down by the drive spin down feature. For disk and midplane types where this processor also controls power to the disk, power-on failure will result in the Error status. The disk is present but the system is having communication problems with the disk LED processor. The disk is present but is not detected by the expander. The values that this measure can report and the their corresponding numeric values are tabulated below: Measure Value Indicates the current state of this disk. Measurements made by the test Measurement Both the normal and abnormal frequencies configured for the detailed diagnosis measures should not be 0.The eG manager license should allow the detailed diagnosis capability.The option to selectively enable/disable the detailed diagnosis capability will be available only if the following conditions are fulfilled: To disable the capability, click on the Off option. To enable the detailed diagnosis capability of this test for a particular server, choose the On option. With this capability, the eG agents can be configured to run detailed, more elaborate tests as and when specific problems are detected. To make diagnosis more efficient and accurate, the eG Enterprise embeds an optional detailed diagnostic capability. If it is SSL-enabled, then change this flag to True. This is why, this flag is set to False by default. By default, this is 60 seconds.īy default, HP P2000 SAN system is not SSL-enabled. Specify the time duration for which this test should wait for a response from the storage system in the Timeout text box. To enable the eG agent to access the management controller, invoke the XML API commands, and collect the required metrics, you need to specify the service port on the controller that listens for HTTP/HTTPS requests for XML API semantics. The Management Controller of the HP P2000 storage system provides access for monitoring and management via the HTTP and HTTPS protocols for XML API request/response semantics. To know how to create such a user, refer to Pre-requisites for monitoring the HP P2000 SAN storage system.Ĭonfirm the password by retyping it here. Specify the login credentials of such a user in the User and Password text boxes. In order to monitor a HP P2000 SAN storage system, the eG agent has to be configured with the credentials of a user who has been assigned the Monitor role. For this purpose, specify the IP address of the alternate controller in the Additional Controller IP text box. If the monitored storage device has two controllers, then you can configure the test to connect to an alternate controller, if the host is unreachable. This is because, the Additional Controller IP is set to none by default. If the Host is unavailable, then the test will not be able to execute. By default, this is NULL.īy default, this test always connects to the Host to collect metrics. The port number at which the specified host listens. In case of a dual-controller configuration, the IP address of the primary controller will be displayed here. Since the storage device is managed using the IP address of its storage controller, the same will be displayed as host. The host for which the test is to be configured. Configurable parameters for the test Parameter ![]() Outputs of the test : One set of results for each physical disk of the HP P2000 SAN storage system being monitored. ![]() Target of the test : A HP P2000 SAN storage systemĪgent deploying the test : A remote agent In addition, this test also reports the LED status of each disk. ![]() This test reports the current status and health of each disk of the HP P2000 SAN storage system. For this purpose, administrators can use the HP P2000 Disk Status test. Administrators should then be able to rapidly identify which disks are in an abnormal state and determine the reason for the abnormality, so that the problems can be solved quickly. ![]() If one/more disks in a storage system experience errors or are faulty or have failed, then users will be unable to access the data stored in the disks. ![]()
0 Comments
Leave a Reply. |